Polybenzimidazole fiber

polybenzimidazole
Identifiers
32075-68-6
Properties
(C20H12N4)n
Molar mass Variable
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
Infobox references

Polybenzimidazole (PBI, short for poly[2,2’-(m-phenylen)-5,5’-bisbenzimidazole]) fiber is a synthetic fiber with a very high melting point. It has exceptional thermal and chemical stability and does not readily ignite. It was first discovered by American polymer chemist Carl Shipp Marvel in the pursuit of new materials with superior stability, retention of stiffness, toughness at elevated temperature. Due to its high stability, polybenzimidazole is used to fabricate high-performance protective apparel such as firefighter’s gear, astronaut space suits, high temperature protective gloves, welders’ apparel and aircraft wall fabrics. In recent years, polybenzimidazole found its application as a membrane in fuel cells.

History

Discovery

Brinker and Robinson invented the first aliphatic polybenzimidazoles in 1949.[1] However the discovery of aromatic polybenzimidazole which show excellent physical and chemical properties was generally credited to Carl Shipp Marvel in the 1950s.[2] The materials Laboratory of Wright Patterson Air Force Base approached Marvel. They were looking for materials suitable for drogue parachutes which could tolerate short-time mechanical stress. However, the thermal resistance of all known filaments at that time was completely inadequate. The original search concentrated on aromatic condensation polymers but the amide linkage proved to be weak link for the aim of maximal thermal stability of the polymer, whereas Marvel’s research focused on condensation polymers with aromatic and heteroaromatic repeating units. This progressively led to the discovery of polybenzimidazole.

Development

Replica Apollo spacesuit, Chemical Heritage Foundation temporary exhibit, 2014

Its development history can be summarized in the following list:[3]

Properties

General physical properties

PBI are usually yellow to brown solid infusible up to 400 °C or higher.[4] The solubility of PBI is controversial, because while most of the linear PBI are partly or entirely dissolved in strong protonic acids (for instance, sulfuric acid or methanesulfonic acid), contradictory observations of solubities have been recorded among weaker acids like formic acid, and in non-acidic media, such as the aprotic amide-type solvents and dimethyl sulfoxide. For example, one type of PBI prepared in phosphoric acid was found by Iwakura et al.[5] to be partially soluble in formic acid, but completely soluble in dimethyl sulfoxide and dimethylacetamide, whereas Varma and Veena[6] reported the same polymer type to dissolve completely in formic acid, yet only partially in dimethyl sulfoxide or dimethylacetamide.

Thermal stability

Imidazole derivatives are known to be stable compounds. Many of them are resistant to the most drastic treatments with acids and bases and not easily oxidized. The high melting point and high stability at over 400 degree suggests a polymer with benzimidazole as the repeating unit may also show high heat stability. Polybenzimidazole and its aromatic derivatives can withstand temperatures in excess of about 500 degrees without softening and degrading. The polymer synthesized from isophthalic acid and 3,3'-diaminobenzidine is not melted by exposure to a temperature of 770 degrees and loses only 30% of its weight after exposure to high temperature up to 900 degrees for several hours.[7] This proves a high thermal stability for PBI.

Flame resistance

A property of a material needed to be considered before putting it into application is flammability, which demonstrates how easily one material can ignite and combust under the realistic operating conditions. This may affect its application in varied areas, such as in construction, plant design, and interior decoration. The quantitative assessment of flammability is based on limiting oxygen index(LOI), i.e., the minimum oxygen concentration at which a given sample can be induced to burn permit a comparison of flammability. Data show that PBI are highly flame resistant material compared to common polymers.[8]

Moisture regain

PBI's remarkable moisture regain is useful in protective clothing; this makes the clothing comfortable to wear, in sharp contrast to other synthetic polymers. The moisture regain ability of PBI (13%) compares favorably with cotton (16%).[9]

Synthesis

The preparation of PBI(IV) can be achieved by condensation reaction of diphenyl isophthalate (I) and 3,3’,4,4’-tetraaminodiphenyl (II) (Figure 1). The spontaneous cyclization of the intermediately formed animo-amide (III) to PBI (IV) provided a much more stable amide linkage.
This synthetic method was first used in the lab and later developed into a two step process. In a typical condition, starting materials were heated at 270 degree for 1.5 h to form the PBI prepolymer and later the prepolymer was heated at 360 degree for another 1 h to form the final commercial-grade product. The reason for the second step is due to the formation of the by-product phenol and water in the first step creating voluminous foam,[10] which leads to the volume expansion of several times of the original. This is the issue that must be considered by the industrial manufacturers. This foam can be reduced by conducting the polycondensation at a high temperature around 200 °C and under the pressure of 2.1-4.2 MPa.[11] The foam can also be controlled by adding high boiling point liquids such as diphenylether or cetane to the polycondesation. The boiling point can make the liquid stay in the first stage of polycondesation but evaporate in the second stage of solid condensation. The disadvantage of this method is that there are still some liquids which remain in PBI and it is hard to remove them completely.[11]

Figure1. The synthetic scheme for polybenzimidazole.


While changing the tetramine and acid, a number of different aromatic poly benzimidazoles have been synthesized. The following table (Table 1)[12] lists out some of the combination possibilities that have been synthesized in the literature. Some of the combination have actually been translated into fibers on a small scale. However, the only significant progress have been made to date is PBI.

Polybenzimidazole derivatives shown in the figure wherein R is an aromatic nucleus symmetrically tetra substituted with the nitrogen atoms of the formula being part of benzimdazole rings. R' being a member of an aromatic hydrocarbon ring.
R(Teraamine) R'(acid))
Benzene Benzene
Diphenyl Diphenyl
Diphenylether Diphenylether
Diphenylsulfone Naphthalene
Naphthalene Pyridine
Pyridine Anthraquinone
Anthraquinone Ferrocene
Anthracene
 Table 1. Other monomers which forms derivatives of polybenzimidazole

The most common form of PBI used in industry is the fiber form. The fiber process following polymerization is shown in the figure. The polymer is made into solution using dimethylacetamide as solvent. The solution is filtered and converted into fiber using a high temperature dry-spinning process. The fiber is subsequently drawn at elevated temperature to get desired mechanical properties. It is then sulfonated and made into staple using conventional crimping and cutting techniques.

The PBI fiber is made in a serial of steps following polymerization to get PBI staple form for direct usage.

Applications

Before the 1980s, the major applications of PBI were fire-blocking, thermal protective apparel, and reverse osmosis membranes. Its applications became various by the 1990s when molded PBI parts and microporous membranes were developed.

Protective apparel

The thermal stability, flame resistance, and moisture regain of PBI and its conventional textile processing character enable it to be processed on conventional staple fiber textile equipment. These characteristics lead to one of the most important applications of PBI: protective apparel. PBI filaments were fabricated into protective clothing like firefighters' gear and astronauts' suits. PBI filaments are dry spun from dimethylacetamide containing lithium chloride. After washing and drying the resulting yarn is golden brown.

Now the fibers used in the protective gear is poly(2,2’-m-phenylene-5,5’-bibenzimidazole) which use tetraaminobipheny as monomer for a better thermo resistance property

PBI fiber is an excellent candidate for applications in severe environments due to its combination of thermal, chemical and textile properties. Flame and thermal resistance are the critical properties of protective apparel. This kind of apparel applications includes firefighter’s protective apparel, astronaut’s suits,[13] aluminized crash rescued gear, industrial worker’s apparel, and suits for racing car drivers.[14]

Nowadays most of the fire fighters' protective gears are made with PBI fiber

The problem of PBI protective apparel is that it keeps heat out but it also keeps the heat in, too. Thus, by the time the firefighters feel heat and pain, it is too late and they will get burnt or killed since it is hard for the heat to penetrate the suit and be released into the air. There are still some major fire departments have not yet switched from old fire gear to PBI due to the fear of what PBI can cause. One example is the Chicago Fire Department, which still relies on the old type of rubber or leather coats.[15]

PBI membranes

PBI has been used as the membranes for various separation purposes. Traditionally, PBI was used semi-permeable membranes for electrodialysis, reverse osmosis or ultrafiltration.[16] Recently PBI is also used for gas separations.[17] [18]due to its close chain packing since PBI has rigidity structure and strong hydrogen bonding. PBI membranes are dense, with very low gas permeability. To be proton conductive, PBI usually is doped with acid. The higher level of the acid doping, the more conductive PBI is. But one problem raised is the mechanical strength of PBI decreases at the same time. The optimum doping level is thus a compromise between these two effects. Thus, multiple methods such as ionic cross-linking, covlant cross-linking and composite membranes[16] have been researched to optimize the doping level at which PBI has an improved conductivity without sacrificing mechanical strength. Kerres et al.[19] recently have recently synthesized sulphonated partially fluorinated arylene main chain polymer. Their blend membranes with PBI demonstrate high level acid-doping levels with thermal and extended stability, high proton conductivities, less acid swelling, reasonable mechanical strength.

Fluorinated sulphonated polymers used for preparation of acid–base blend membranes with PB. The blend membranes with PBI have excellent thermal and extended stability

Molded PBI resin

PBI resin is molded via a sintering process that was jointly developed by Hoechst Celanese (North Carolina, USA) and Alpha Precision Plastics, Inc. (Houston, Texas, USA).[20] Molded PBI resin is an excellent candidate for high strength, low weight material. Since it has the highest compressive strength, 58 ksi, of any available, unfilled resin and other mechanical properties such as a tensile strength of 23 ksi, a flexural strength of 32 ksi, a ductile compressive failure mode and the relatively low density of 1.3 g/cm3.[21] Moreover, its thermal and electrical properties also make it a well known thermoplastic resin. The PBI resin comprises a recurring structural unit represented by the following figure.

The recurring structural unit for PBI resin


According to the Composite Materials Research Group at the University of Wyoming, PBI resin parts maintain significant tensile properties and compressive strength to 700 °F (371 °C). PBI resin parts are also potential materials for the chemical process and oil recovery industries which have demands of thermal stability and chemical resistance. In these areas, PBI resin has been successfully applied in demanding sealing, for instance, valve seats, stem seals, hydraulic seals and backup rings. In the aerospace industry, PBI resin has high strength and short term high temperature resistance advantages. In the industrial sector, PBI resin's high dimensional stability as well as retention of electrical properties at high temperature make it used as a thermal and electrical insulator.[14]

Fuel cell electrolyte

Polybenzimidazole is able to be complexed by strong acids because of its basic character. Complexation by phosphoric acid makes it a proton conductive material.[22] This renders the possible application to high temperature fuel cells. Cell performance test show a good stability in performance for 200 h runs at 150 degree. Application in direct methanol fuel cells may be also of interest because of a better selectivity water/methanol compared to existing membranes. Wainright, Wang et al. reported that PBI doped with phosphoric acid was utilized as a high temperature fuel cell electrolyte.[23] The doped PBI high temperature fuel cell electrolyte has several advantages. The elevated temperature increases the kinetic rates of the fuel cell reactions. It also can reduce the problem of the catalyst poisoning by adsorbed carbon monoxide and it minimizes problems due to electrode flooding.[22] PBI/H3PO4 is conductive even in low relative humidity and it allows less crossover of the methanol at the same time.[24] These contribute PBI/H3PO4 to be superior to some traditional polymer electrolytes such as Nafion. Additionally, PBI/H3PO4 maintains good mechanical strength and toughness.[24] Its modulus is three order of magnitudes greater than that of Nafion.[25] This means that the thinner films can be used, thus reducing ohmic loss.

In phosphoric acid doped PBI, the phosphoric acid groups are not directly bonded to the polymer backbone. Instead, the low charge density anion is immobilized and linked to the structure by a strong hydrogen-bond network.

Asbestos replacement

Previously, only asbestos can well perform in temperature gloves such as for foundries, aluminum extrusion, and metal treatment, while PBI trials have been developed and show adequately functions as asbestos. Moreover, a safety garment manufacturer reported that gloves containing PBI outlasted asbestos two to nine times with an effective cost.[26] Gloves containing PBI fibers are softer and more supple than those made of asbestos, offering, the worker greater mobility, and comfort even if the fabric becomes charred. Besides, PBI fiber avoids the chronic toxicity problems associated with asbestos because it processes on standard textile and glove fabricating equipment.[27] PBI also can also be a good substitute for asbestos in several areas of glass manufacturing.

Flue gas filtration

PBI’s chemical, thermal and physical properties demonstrate that it can be a promising material as a flue gas filter fabric for coal-fired boilers. Few fabrics can survive in the acidic and high temperature environment encountered in coal-fired boiler flue gas.[28] The filter bags also must be able to bear the abrasion from the periodic cleaning to remove accumulated dust. PBI fabric has a good abrasion resistance property. The acid and abrasion resistance and thermal stability properties make PBI a competitor for this application.

References

  1. ↑ "Patent on aliphatic polybenzimidazole". Retrieved 7 March 2014.
  2. ↑ Leonard, Nelson. "A Biographic Memoir of Carl Shipp Marvel" (PDF). National Academy of Sciences. Retrieved 13 February 2014.
  3. ↑ "PBI History". Retrieved 14 February 2014.
  4. ↑ Synthesis and degradation, rheology and extrusion. Berlin u.a.: Springer. 1982. ISBN 978-3-540-11774-2. |first1= missing |last1= in Authors list (help)
  5. ↑ Iwakura, Yoshio; Uno, Keikichi; Imai, Yoshio (June 1964). "Polyphenylenebenzimidazoles". Journal of Polymer Science Part A: General Papers. 2 (6): 2605–2615. doi:10.1002/pol.1964.100020611.
  6. ↑ Varma, I. K.; Veena, (April 1976). "Effect of structure on properties of aromatic-aliphatic polybenzimidazoles". Journal of Polymer Science: Polymer Chemistry Edition. 14 (4): 973–980. Bibcode:1976JPoSA..14..973V. doi:10.1002/pol.1976.170140417.
  7. ↑ Vogel, Herward; Marvel, C. S. (April 1961). "Polybenzimidazoles, new thermally stable polymers". Journal of Polymer Science. 50 (154): 511–539. Bibcode:1961JPoSc..50..511V. doi:10.1002/pol.1961.1205015419.
  8. ↑ van Krevelen, Dirk W. (30 March 1972). "New developments in the field of flame-resistant fibres". Angewandte Makromolekulare Chemie. 22 (1): 133–157. doi:10.1002/apmc.1972.050220107.
  9. ↑ Demartino, R. N. (1 August 1984). "Comfort Properties of Polybenzimidazole Fiber". Textile Research Journal. 54 (8): 516–521. doi:10.1177/004051758405400803.
  10. ↑ Chung, Tai-Shung (1 May 1997). "A Critical Review of Polybenzimidazoles". Polymer Reviews. 37 (2): 277–301. doi:10.1080/15321799708018367.
  11. 1 2 Kricheldorf, edited by Hans R. (1992). Handbook of polymer synthesis. (dernière ed.). New York: Marcel Dekker. ISBN 0-8247-8514-2.
  12. ↑ Belohlav, Leo R. (10 December 1974). "Polybenzimidazole". Angewandte Makromolekulare Chemie. 40 (1): 465–483. doi:10.1002/apmc.1974.050400122.
  13. ↑ Kirshenbaum, edited by Raymond B. Seymour, Gerald S. (1987). High Performance Polymers: Their Origin and Development Proceedings of the Symposium on the History of High Performance Polymers at the American Chemical Society Meeting held in New York, April 15-18, 1986. Dordrecht: Springer Netherlands. ISBN 978-94-011-7075-8.
  14. 1 2 Sandor, R.B. (1990). "PBI (Polybenzimidazole): Synthesis, Properties and Applications". High Performance Polymers. 2 (1): 25–37. doi:10.1177/152483999000200103 (inactive 2015-02-01).
  15. ↑ Mager, David. "EVALUATING THE RESULTS OF A MODIFIED BUNKER GEAR POLICY" (PDF). Retrieved 9 March 2014.
  16. 1 2 Li, Qingfeng; Jensen, Jens Oluf; Savinell, Robert F.; Bjerrum, Niels J. (May 2009). "High temperature proton exchange membranes based on polybenzimidazoles for fuel cells". Progress in Polymer Science. 34 (5): 449–477. doi:10.1016/j.progpolymsci.2008.12.003.
  17. ↑ Kumbharkar, S.C.; Li, K. (October 2012). "Structurally modified polybenzimidazole hollow fibre membranes with enhanced gas permeation properties". Journal of Membrane Science. 415-416: 793–800. doi:10.1016/j.memsci.2012.05.071.
  18. ↑ Li, Xin; Singh, Rajinder P.; Dudeck, Kevin W.; Berchtold, Kathryn A.; Benicewicz, Brian C. (July 2014). "Influence of polybenzimidazole main chain structure on H2/CO2 separation at elevated temperatures". Journal of Membrane Science. 461: 59–68. doi:10.1016/j.memsci.2014.03.008.
  19. ↑ Kerres, Jochen A.; Xing, Danmin; Schönberger, Frank (15 August 2006). "Comparative investigation of novel PBI blend ionomer membranes from nonfluorinated and partially fluorinated poly arylene ethers". Journal of Polymer Science Part B: Polymer Physics. 44 (16): 2311–2326. Bibcode:2006JPoSB..44.2311K. doi:10.1002/polb.20862.
  20. ↑ Ward, B.C (1987). "32nd SAMPE Int. Symp.," (32): 853.
  21. ↑ Sandor, R.B. (1990). "PBI (Polybenzimidazole): Synthesis". High Performance Polymers. 2 (1): 25–37. doi:10.1177/152483999000200103 (inactive 2015-02-01).
  22. 1 2 Samms, S. R. (1996). "Thermal Stability of Proton Conducting Acid Doped Polybenzimidazole in Simulated Fuel Cell Environments". Journal of the Electrochemical Society. 143 (4): 1225. doi:10.1149/1.1836621.
  23. ↑ Wainright,, J.S.; Wang, J.-T., Weng, D., Savinell, R.F., Litt, M (July 1995). "Acid-doped polybenzimidazoles: A new polymer electrolyte". Journal of the Electrochemical Society. 142 (7): L121–L123. doi:10.1149/1.2044337.
  24. 1 2 Zhao, edited by T.S. (2009). Micro fuel cells : principles and applications. Burlington, MA: Academic Press. ISBN 9780123747136.
  25. ↑ Buckley, A (1988). Encyclopedia of Polymer Science And Engineering,. New York: John Wiley & Sons.
  26. ↑ Coffin, D.R.; Serad, G.A.; Hicks, H.L.; Montgomery, R.T. (1 July 1982). "Properties and Applications of Celanese PBI--Polybenzimidazole Fiber". Textile Research Journal. 52 (7): 466–472. doi:10.1177/004051758205200706.
  27. ↑ Celanese. "PBI in High Temperature Protective Gloves" (PDF). Retrieved 9 March 2014.
  28. ↑ Hearle, ed. by J.W.S. (2004). High-performance fibres (Repr. ed.). Boca Raton, Fla. [u.a.]: CRC Press. ISBN 1855735393.

Appendix of properties

PBI fiber characteristics

The chemical formula of poly[2,2’-(m-phenylen)-5,5’ bibenzimidazol] (PBI) is believed to be: ([NH-C=CH-C=CH-CH=C-N=C-]2-[C=CH-C=CH-CH=CH-])n OR (C20N4H12)n of Molar mass 308.336 ± 0.018 g/mol.

Chemical resistance

Chemical Resistance Grade
Acids - concentrated Poor
Acids - dilute Fair-Poor
Alcohols Good
Alkalis Good-Poor
Aromatic hydrocarbons Good
Greases and Oils Good
Halogenated Hydrocarbons Good
Ketones Good

It is dyeable to dark shades with basic dyes following caustic pretreatment and resistant to most chemicals.

Electrical properties

Electrical Properties
Dielectric constant @ 1 MHz 3.2
Dielectric strength 21 kV·mm−1
Volume resistivity 8x1014 Ω·cm

Features low electrical conductivity and low static electricity buildup.

Mechanical properties

Mechanical Properties
Coefficient of friction 0.19-0.27
Compressive modulus 6.2 GPa
Compressive strength 400 MPa
Elongation at break 3%
Hardness - Rockwell K115
Izod impact strength 590 J·m−1 unnotched
Poisson's ratio 0.34
Tensile modulus 5.9 GPa
Tensile strength 160 MPa

Features abrasion resistance.

Physical Properties

Physical Properties
Char Yield (under pyrolysis) High
Density 1.3 g/cm3
Flammability Does not burn
Limiting oxygen index 58%
Radiation resistance Good
Water absorption - over 24 hours 0.4%

Additional features: will not ignite or smolder (burn slowly without flame), mildew- and age-resistant, resistant to sparks and welding spatter.

Thermal Properties

Thermal Properties Grade
Coefficient of thermal expansion 23×10−6·K−1 Low
Heat-deflection temperature - 0.45 MPa 435 °C (815 °F) High
Thermal conductivity @ 23 °C (73 °F) 0.41 W·m−1·K−1 Low
Upper working temperature 260–400 °C (500–752 °F) High

Other features: continuous temperature: 540 °C (1,004 °F), does not melt but degrades around the temperature: 760 °C (1,400 °F) under pyrolysis, retains fiber integrity and suppleness up to 540 °C (1,004 °F).

This article is issued from Wikipedia - version of the 11/22/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.