Dowding system

This illustration shows the Dowding reporting chain for a highlighted Sector. ROC reports flow back through the Sector controls to FCHQ; it does not show the radars. Information flows back from FCHQ to Group, between groups, and down to Sectors, and then to the defences.

The Dowding system^{[lower-alpha 1]} was the world's first wide-area ground-controlled interception network,^[2] controlling the airspace across the United Kingdom from northern Scotland to the southern coast of England. It used a widespread dedicated land-line telephone network to rapidly collect information from Chain Home (CH) radar stations and the Royal Observer Corps (ROC) in order to build a single image of the entire UK airspace and then direct defensive interceptor aircraft and anti-aircraft artillery against enemy targets. The system was built by the Royal Air Force just before the start of World War II, and proved decisive in the Battle of Britain.

The Dowding system was developed after tests demonstrated problems relaying information to the fighters before it was out of date. Air Chief Marshal Hugh Dowding, commander of RAF Fighter Command, solved the problem through the use of hierarchical reporting chains. Information was sent to Fighter Command Headquarters (FCHQ) central filter room at Bentley Priory and used to prepare a map of the battle. Details of the map were then relayed to the Group and Sector headquarters, where operators re-created the map at a scale covering their area of operations. Looking at the maps, commanders could make decisions on how to employ their forces quickly and without clutter. Instructions were relayed to the pilots only from the squadron's sector control rooms, normally co-located at the fighters' operating bases.

The Dowding system is considered key to the success of the RAF against the German air force (Luftwaffe) during the Battle of Britain. The combination of early detection and rapid dissemination of that information acted as a force multiplier, allowing the fighter force to be used at extremely high rates of effectiveness. In the pre-war period, interception rates of 30% to 50% were considered excellent; that meant that over half the sorties sent out would return without having encountered the enemy. During the Battle, average rates were around 90%, and several raids were met with 100% success rates.^[3] Lacking their own direction system, Luftwaffe fighters had little information on the location of their RAF counterparts, and often returned to base having never seen them. When they did, the RAF fighters were almost always in an advantageous position.

Although many histories of the Battle of Britain comment on the role of radar, it was only in conjunction with the Dowding system that radar could be truly effective. This was not lost on Winston Churchill, who noted that:

Development

Previous systems

To counter air raids on London during World War I, E. B. Ashmore constructed a system known as the London Air Defence Area (LADA).^[5] Ashmore put defensive weapons into three rings around the city, searchlights and anti-aircraft artillery in the outer ring, fighter aircraft in the middle ring, and the innermost ring in the city contained more anti-aircraft guns.^[6] Ashmore set up a large plotting table in the Horse Guards in London. Information from spotters was relayed to this central room where wooden blocks were placed on a large map to indicate the location of aircraft and other information. Observers around the map could relay this information to one of 25 regional control rooms, who re-created the portions of the map relevant to them and passed the information to the various weapons in their region.^[6]

After the war, LADA was run by a War Office department known as Air Defence of Great Britain (ADGB). ADGB was responsible for the defence of the entire British Isles during the 1920s and 30s. LADA became the Metropolitan Area, and ADGB expanded on Ashmore's system to deal with longer ranged and faster moving aircraft. Coloured markers matched coloured areas on a sector clock marking off five-minute intervals. As plots were called in, the plotters used markers with the colour pointed to by the clock, which produced multi-coloured paths of markers on the table making easily followed tracks; the freshness of the information could be determined the colour of the latest marker. An identical system was later set up in The Midlands.^[7]

The system lacked early detection, which was deemed essential as the performance of aircraft improved.^[8] Experiments with acoustic mirrors and similar devices were carried out but these always proved unsatisfactory, with detection rates often as low as 5 miles (8.0 km) even in good conditions. Lacking an alternative, in December 1934, the Air Ministry (AM) made plans to deploy sound detection devices around London as part of the Thames Estuary plan.^[8]

RDF

Chain Home coverage 1939–1940 extended over the entire British Channel area and some of France.

A month after the Thames Estuary plan was approved, the Tizard Committee was formed to consider newspaper reports about a German radio powered death ray. The committee consulted a radio expert Robert Watt for a judgement on the report.^{[lower-alpha 2]} Watt asked his assistant, Arnold Wilkins, to carry out the necessary calculations. Wilkins quickly concluded that it was impossible; the amount of radio energy needed would be well beyond the state of the art of existing electronics. When Watt asked about alternatives, Wilkins recalled a General Post Office (GPO) report on aircraft causing fading in radio reception, and suggested that this effect might be used to detect aircraft at long range. The two wrote a joint memo on the concept and returned it to the Tizard Committee in time for their first formal meeting in late January 1935.^[9]

The committee seized upon the concept as a potential solution to the problem of bomber detection and the fear that the bomber will always get through. A second memo with more detailed calculations arrived in February and was shown to the Air Member for Supply and Research, Hugh Dowding. He was impressed with the concept, but wanted a practical demonstration. This was carried out on 26 February 1935, now known as the Daventry Experiment, which clearly indicated the presence of a nearby aircraft. Dowding immediately released funding for development. By the summer of 1935 the system, code-named "RDF", was able to detect bomber-sized targets at ranges of 60 miles (97 km). Plans were made to build a chain of RDF stations at about 25 miles (40 km) intervals along the English coast in a system called Chain Home (CH).^[10]

On 27 July, Henry Tizard suggested running a series of experiments of fighter interception, based on an estimated fifteen-minute warning time that RDF would provide. A seven-month-long series of tests began in the summer of 1936 at Biggin Hill, under the direction of Wing Commander Eustace Grenfell aided by a navigation expert, Squadron Leader Robert Linton Ragg.^[10] Gloster Gauntlet fighters intercepted virtual aircraft, civilian airliners and then Bristol Blenheim light bombers.^[11]

The first interceptions were calculated using trigonometry and mechanical calculators but eventually Grenfell had enough of the "confounded machines" and directed a perfect interception by eye.^{[12][lower-alpha 3]} Tizard introduced the equal angles method of rapidly estimating an interception point, by imagining the fighters and bombers at the opposite corners on the base of a triangle. The bombers were flying at a particular angle to the base and the controller sent the fighters along the opposite angle, to converge with the target at the apex of the triangle. With this Tizzy Angle, interception rates shot up and by the end of 1936 they were consistently above 90 percent when the altitude was known and did not change. If the bombers changed their altitude, or the fighters arrived below them, manoeuvring for the attack reduced the success rate to about 60 percent.^{[13][lower-alpha 4]}

Teething trouble

Dowding's support for radar was matched by his understanding that radar alone was not a panacea.

ADGB was disbanded in 1936, its duties were handed to the Air Ministry, and divided into Fighter Command and Bomber Command. Dowding was promoted to Air Officer Commanding-in-Chief of Fighter Command on its creation on 6 July 1936.^[11] The first operational CH station was set up at the radar researchers' new laboratory at Bawdsey Manor. In spite of rapid progress, RDF still had teething problems, on one occasion, Dowding was watching the displays of the test system for a sign of the attackers, when he heard them overhead.^[14] These problems were remedied over the next year and in April 1937, tests using the prototype CH radar at Bawdsey demonstrated great promise, allowing the controllers to measure the altitude of the aircraft to within 2,000 feet (610 m), which greatly reduced the altitude problem.^[13]

To increase warning time, the CH systems were built close to the shore facing out to sea, placing them as close to the enemy as possible. This meant they provided no information for friendly fighters on the way to the attack, or of enemy aircraft once they crossed the coast. For these areas, Dowding planned to rely on the existing Observer Corps (OC) system that Fighter Command inherited from ADGB.^{[lower-alpha 5]} Using different equipment, the reports from CH and the ROC were sometimes contradictory, and the volume of information supplied by the national network was overwhelming.^[15] An added problem was the lack of identification of the aircraft; CH could not discriminate between friendly and hostile aircraft at that time,^[16] and the OC could not discriminate between friendly and enemy fighters when they were flying at high altitude.

To address the problem of identification, Dowding pressed for a supply of high-frequency direction finding (huff-duff) sets, which could locate the fighters using their existing radio sets. This led to the introduction of the "pip-squeak" system that was widely available from early 1940, along with the first identification friend or foe (IFF) transponders which were widespread by October 1940. This solved the identification problem, but meant that there were now three sources of information, RDF, OC and huff-duff, none of which had a complete picture of the airspace.^[13]

Building the system

Patrick Blackett's work on the Dowding system would form the basis of the field of mathematics known as operations research.

Dowding recognised that the main problem was not technical but too many sources of information, none of them with complete coverage and none able quickly to report useful information to the fighters. Dowding, Tizard and a mathematician Patrick Blackett, another founding member of the committee, began to evolving a new system from that inherited from ADGB.^[17][18]

To handle the mass of data and the potential for overlap, Dowding instituted a policy of sending all location reports from the radars to a new fighter direction centre at Fighter Command headquarters. This mimicked the system the OC had already set up for co-ordinating the reports from many individual spotters into a map covering a larger area. The new system did the same at a far larger scale, all of the UK, adding in reports from the top level of the OC. Telephone operators in contact with the RDF and OC centers relayed reports to workers around the map, who used these reports to place small coloured markers on the map, with the colour indicating the time that the report was received. The markers formed lines which as they elongated, indicated the location and direction of the targets; each cluster was assigned a number, its track.^[17]

As the paths of the targets became clear over time, operators observing the map picked tracks heading towards the various fighter groups and forwarded the information to the group headquarters. The group HQs used these reports to recreate a portion of the master map containing just the tracks relevant to them. Commanders at the group headquarters could easily picture the battle and assign fighters to targets. Targets assigned to squadrons within a sector were forwarded in this same fashion to the sector headquarters, which recreated the map at an even smaller scale, using this map to guide their fighters.^[17]

By early 1939, the basic system had been built out, and from 11 August 1939, Bomber Command was asked to launch a series of mock attacks using aircraft returning from exercises over France. Reports from No. 11 Group RAF were enthusiastic, stating that "RDF information and plotting throughout the Exercise was consistently first-rate, and enabled interceptions to be effected on the Coast", to which Dowding added "daylight raids were normally tracked and intercepted with ease and regularity".^[17]

Description

Filtering

The first improvement Dowding suggested was to add a filter room at FCHQ, where all CH reports were sent.^[19] CH stations converted their angle and range measurements into a location on the Ordnance Survey National Grid,^[5] A telephone operator, or teller, forwarded this location to the filter room, where a plotter would place a small coloured marker at that location on a large map covering most of the UK, the colours being the same as those adopted by the Observer Corps. The rapidity of reporting caused plot markers to pile up on the map, which became quite cluttered during larger missions. Since each station had inaccuracies, the plots spread out on the map.^[15]

Observers watching the progress of plots, tried to determine which of these represented one group of aircraft. When they were confident that a group of markers was a formation, a wooden block was placed on the map in the middle of the plots and numbers and letters placed on the block, to indicate the aircraft type, number and altitude and each block was given a track number. The block would be periodically moved or revised as further plot markers were placed on the board and as it moved, plotters left small arrow-shaped pointers to illustrate where it had been. Once created, the entire network used the same track numbers, from the radar operators who could be asked to revise information for a given track, to the pilots intercepting them.^[15]

Around and above the map were more tellers who controlled the communications, connecting incoming reports to the plotter on the floor nearest that location on the map or connecting incoming requests for information to another teller who could read the map. Tellers examined the track markers, whose larger print allowed them to see the information, although this sometimes required opera glasses.^[20] Sometimes information would have to be plotted that came from an external source, not normally part of the reporting chain; a fighter calling an SOS would report this through his radio on an emergency frequency, which would be picked up by the closest listening post. This information would also flow into the filter room but they were not connected to the plotters on the floor. Operators above the map could mark locations of interest using theatrical spotlights and filters allowed them to change the message being projected.

Reporting hierarchy

11 Group's Operations Room is now known as the Battle of Britain Bunker. On the plotting table are numerous plots. The sector clock on the wall behind the map has coloured 5 minute regions matching the colours on the plots. Above the clock is the main tote board showing the status of the various airfields and their squadrons.

This close-up of a Group level marker indicates that 20 enemy aircraft at 25,000 ft (7,600 m) are being intercepted by 92 and 72 Squadrons of Biggin Hill.

The second improvement introduced by Dowding was aimed at reducing the amount of information being sent to the pilots, and speeding its delivery. For this task, Dowding introduced a hierarchy of control and information flow which ensured that only the information the pilots needed was forwarded to them. At the topmost level was FCHQ filter room, located at Bentley Priory. FCHQ maintained an overall view of the entire battlespace. This information was then forwarded one step down a hierarchy, to the Groups.^[5]

During the Battle of Britain the defensive fighters were split among four active Groups, 10 through 13. 11 Group, which handled most of the fighting, had its plotting room located in the Battle of Britain Bunker (RAF Hillingdon) at Uxbridge, not far from FCHQ. 12 Group, covering the Midlands, was located at Hucknall (and later Watnall), 13 Group in a quarry in Blakelaw outside Newcastle, and the late-formed 10 Group in the aptly named Box outside Bath.^[5]

At the Group HQs another plotting board, covering only the area of interest to that Group, re-created the plots from FCHQ via position reports sent to them over the telephone. This allowed the Groups to re-create the map, but on a scale and location more suitable to their area of operations.^[21] Since the information was being pre-filtered, these maps did not have to be changed as often, and a somewhat simpler marker solution was adopted. Small wooden blocks with tags were placed on the map to represent the location of various formations, indicated by the ID number created in the filter room. The tags indicated the ID number, friend or foe status if known ("H" meant "hostile, F for "friendly"), the estimated number of aircraft, and their altitude. The colour of the altitude tags indicated when the report was updated, matching the same sector clock pattern used at FCHQ. This allowed observers to quickly determine whether or not a plot was up to date, and request updates if needed.^[22] If a target was assigned squadrons for interception, these were indicated with cocktail stick-like tags with the squadron number on them.^[23]

Each Group was split into several Sectors, which handled operations for one or more airfields. This formed the lowest level of the hierarchy, based at the Sector Controls, normally co-located at one of the sector's airfields. For instance, 11 Group was split into sectors A through F running anticlockwise from the south-west to north-east, along with Sector Z to the northwest. A typical sector, Sector C which saw considerable action, was controlled out of Biggin Hill, but also contained another major airbase at West Malling (Maidstone).^[5] Telephone links from Sector to Group allowed the Group's version of the map to be re-created at the Sector, again filtering out information that was not of interest in that area.^[24]

It was the Sector Controls that were responsible for communication with the pilots, as well as barrage balloon and anti-aircraft batteries, providing early warning of the approach of the enemy or warning them not to fire on friendlies.^[5] To combat the problem that the fighter pilots tended to ignore orders from paper pushers, Sector Commanders were normally former pilots themselves, either retired or on medical leave. Dowding, Blackett and Tizard personally drove home the fact that the pilots could not simply hunt for their targets, and had to follow the instructions of the operations centres.^[15]

By creating this system, information flow was primarily in one direction, and continued to be split out on the way down. For instance, the filter room might be receiving 15 reports per minute from various CH sites, but these would be about formations that might cover the entire coast of Great Britain. Portions of these reports, say those over Kent, would be sent to 11 Group, while others, the attack on RAF Driffield for instance, would only be relayed to 13 Group. In turn, 11 Group's operations room would relay only those tracks of interest down to the sectors, filtering out tracks that were out of their range, or being handled by other sectors. Finally, the sector operators only had to relay information to the pilots that actually had an effect on their flight – data about other formations was not relayed, freeing the radio time.

Information sources

The tall towers of the Chain Home system allowed them to detect targets as far as 100 miles away, over France.

A ROC plotter sights an aircraft with his Post Instrument plotter. ROC reports began to flow in as the enemy approached the shoreline.

Chain Home offered an enormous improvement in early detection times compared to older systems of visual or acoustic location. It was not uncommon for CH stations on the southeast coast of Kent to detect enemy raids as they were still forming up over their airfields in France. Additionally, this information was available day or night, in any weather. However, to provide maximum warning time, the CH stations had to be placed as close to the shore as possible. As they could only locate objects in front of them, this meant that CH provided no service over land. This required two additional locating services.^[5]

The task of tracking enemy aircraft over land fell to the Royal Observer Corps. Because of the large number of ROC stations and the relatively small areas they covered, information duplication and overload was a concern. For this reason, information from the ROC was sent to a parallel system of Observer Centres, who acted as both filter and communications stations. This pre-filtered information was then sent into the Dowding reporting chain.^{[5][lower-alpha 6]}

Likewise, a separate reporting chain was tasked with tracking friendly aircraft through the use of radio direction finding (RDF) on their radio transmissions, using a system known as Huff-Duff (receivers) and pip-squeak (transmitter).^[22] Developing a fix using RDF requires two or more observation locations spread apart by some distance and then using triangulation on their reports. In this case three stations were typically used, located about 30 miles (48 km) apart. This information was reported to a selected Sector Control, who used this to plot their locations and pass on that information to the main operations plot. Controllers could then give directions the squadrons. Locations of the fighters were sent up the chain only as required.^[25]

Finally, information on the status of the fighter squadrons was known to the Sectors but needed by the Groups to choose which squadrons to commit. For this task, operations rooms also contained a series of blackboards and electrical lamp systems indicating the force strengths of the fighter squadrons and their current status. Known as the "tote board", this allowed commanders to tell at a glance which units were available to receive commands. The statuses were Released (not available); Available (able to be airborne in 20 minutes); Readiness (airborne in 5 minutes); Standby (pilots in cockpit, airborne in 2 minutes); Airborne and moving into position; Enemy sighted; Ordered to land; Landed and refuelling/rearming. Next to the tote board was a weather board. It was the responsibility of the Women's Auxiliary Air Force (WAAF) plotters^{[lower-alpha 7]} to continually update the tote and weather boards, and relay that information up the chain.^{[26][lower-alpha 8]}

Command

One of the best developed control rooms was for No. 10 Group, located at RAF Box in Wiltshire.

The Sector Control room at Duxford controlled the area from London to The Wash. Radio and telephone operators sat on the upper level, with plot operators in chairs around the map.

The most visible part of the Dowding System were the "operations rooms". The most advanced of these were located at FCHQ and Group HQs. These rooms typically consisted of three layers: a large plotting table on the lowest level, communications operators located at desks around and above the plot, and a second storey above the plot, sometimes behind glass, where commanders could observe and communicate.^[22]

Command of the battle was devolved to the group.^[19] Observing the map from above, group commanders could track the movements of enemy aircraft through their patch, examine the tote board, select a squadron and called their sector to have them scramble. The orders could be as simple as "Squadron nine-two, intercept hostile two-one".^[24] The sector would then phone the office for that squadron (often nothing more than a small shack) and order the aeroplanes to be scrambled.

After forming up, the sector controller asked the squadron to set up their pip-squeak system so they could be tracked. Once their location was measured and transferred to the sector plotting table, the controller would relay instructions to the formation leader. Vectoring was accomplished using the methods developed in the Biggin Hill exercises in 1935, with the sector commander comparing the location of the friendly aircraft with the hostile plots being transferred from group and arranging the interception.^[12] As the fighters were faster and often reached the interception point first, they orbited the location, giving them time to climb and seek an advantageous position.

Squadrons, bases and enemy formations were assigned code words to ease communication speed and accuracy. Amendments from sector control at Biggin Hill to 72 Squadron would take the general form "Tennis leader this is Tophat control, your customers are now over Maidstone, vector zero-nine-zero, angels two-zero"; the Biggin Hill controller (Tophat) was asking 72 Squadron (Tennis) to fly due east (vector zero-nine-zero) at 20,000 feet (6,100 m) (angels two-zero) to intercept their target. The sector was also responsible for local gun and balloon defences and getting the fighters safely back to an airfield after the sortie.

Physical construction

Group 11's operations room was completely underground, its entrance is now watched over by a Spitfire gate guard.

FCHQ and Group Control centres, in keeping with their importance in the battle, were located in bomb-proof bunkers away from airfields. Most of these were built just before the war. Communications were ensured by hundreds of miles of dedicated phone lines laid by the GPO and buried deep underground to prevent them from being cut by bombs.

Sector Control centres tended to be relatively small, and were mostly housed in brick, single-storey, tile-roofed structures above ground, where they were vulnerable to attack. By 1940, most were semi-protected by an earth bank or "blast wall" surrounding them which reached as high as the eaves. Fortunately, Luftwaffe Intelligence was unaware of the importance of these rooms and most were left alone.

The control rooms at Biggin Hill were destroyed by a raid on 31 August, but this was due to a chance bomb hit. As a further precaution, emergency control rooms were set up in different locations away from the airfields, with small loss in efficiency; Kenley, for example, could use an alternative room housed in a butcher's shop in nearby Caterham.^[26]

The vulnerability of the earlier rooms was appreciated, and new airfields built during the expansion programme of the 1930s used bombproof Mk. II, L-shaped structures.

Effects on the battle

The German Freya early warning radar was a match for British units. Early detection alone was not enough, however; the information needed to be relayed to the pilots.

The effect of this system was profound, and remains a widely used example of the concept of force multiplication.^[27] Before the introduction of radar the task of interception appeared to be increasingly difficult, if not impossible. As bomber speeds and altitudes grew, the time available to arrange an interception was dropping. Although fighter performance was also increasing, certain aspects like getting the pilot into the aircraft and taking off introduced fixed overheads that did not improve. With the only detection means being the observers and acoustic location with ranges on the order of 20 mi (32 km) under the very best conditions, the bombers would be over their targets before the spotters could call in the raid and the fighters could climb to their altitude.^[3]

Given this lopsided balance of power, fighter operations prior to the introduction of radar were generally in the form of standing patrols or "sweeps", with the fighters being sent up to fly along a pre-arranged path or area in the hopes of encountering the enemy. During World War I interception missions, the vast majority of patrols returned home without ever having seen the enemy. The same was true for all forces during the Battle of France, where 30% interception rates were considered typical, and 50% excellent.^[3]

In the case of an attack by a high-speed force, the attackers could pick the time and place of the attack, and expect to encounter only the aircraft already in the air along that route. Thus they could outnumber the defenders in any given area. To ensure there were a reasonable number of fighters along any approach route, huge numbers of aircraft would need to be in the air at all times covering all the routes. Even more aircraft would be needed to handle issues like refuelling, re-arming, and repair. Likewise, a huge number of pilots would be needed to crew the aircraft, as each pilot could only be expected to fly so long per day. Such a system was essentially impossible, and was one of the reasons it was widely believed that "the bomber will always get through".^[28]

The unified view of the battlespace provided by the Dowding system turned the tables in favour of the defence. By rapidly sending accurate, timely information to the fighters, their ability to find and attack the enemy was dramatically increased, and the time required to do so decreased. The fighters took off, flew directly to their targets, engaged and returned directly to their bases. In early operations interception rates of 75% were routine, and this number continued to improve as the operators became more familiar with their tasks. By the end of the Battle of Britain, rates of interception over 90% were becoming common, and several raids were met with 100% interception rates.^[3] In numerical terms, it was as if Fighter Command had over twice as many fighters, giving them effective parity with the Luftwaffe.

While CH was being installed in the UK, the Germans were working on their own radar systems and had deployed an excellent early-warning system known as "Freya". But the complexity of relaying the information from the radars to the fighters had not been addressed, and was apparently never seriously considered at the time. During the Battle of the Heligoland Bight in 1939, over 100 German aircraft were scrambled to meet a small force of RAF bombers, but less than half of these found them. This was in spite of a Luftwaffe Freya detecting the raid while still one hour out, there was no way for this unit to communicate with the fighters. The only radar reports to reach them came from a naval Freya near the target, too late to improve matters.^[29]

Likewise, the Opana Radar Site detected the attack on Pearl Harbor about an hour before it reached the island. They telephoned the communications office that was in charge of disseminating such information and made their report. The office had been informed that a flight of B-17 Flying Fortress bombers would be arriving that day, but lacked any sort of information on their location, at that time far to the east. The communications officer, Lt. Kermit Tyler, concluded the radar site had spotted the bombers, and failed to pass on the warning. The Japanese attack went unopposed.^[30]

It was only through the combination of all of the elements of the Dowding system that an effective defensive network was created. Peter Townsend later noted that:

The Germans knew about British radar but never dreamed that what the radar 'saw' was being passed on to the fighter pilot in the air through such a highly elaborate communications system.^[19]

During the war, the Luftwaffe consistently underestimated the value of the system. A 16 July 1940 Luftwaffe intelligence report failed to even mention it, in spite of being aware of it through signals intercepts, and having complete details of its World War I predecessor. A later report on 7 August did make mention of the system, but only to suggest that it would tie fighters to their sectors, reducing their flexibility and ability to deal with large raids.^[31]

While discussing the events with British historians immediately after the war, Erhard Milch and Adolf Galland both expressed their belief that one or two CH stations might have been destroyed during early raids, but they proved difficult targets. This was true; several stations had been knocked out of service for a time, while others managed to maintain operations in spite of attacks. But the historians interviewing them noted "neither seemed to realize how important were the RDF stations to Fighter Command technique of interception or how embarrassing sustained attacks upon them would have been."^[31]

This realisation must have sunk in over time; after the war Galland noted:

From the first the British had an extraordinary advantage, never to be balanced out at any time during the whole war, which was their radar and fighter control network and organization. It was for us a very bitter surprise. We had nothing like it. We could do no other than knock frontally against the outstandingly well-organized and resolute direct defence of the British Isles.^[32]

Problems

Although the Dowding system proved itself in combat, the system and command of the battle had several problems. A huge volume of information flowed through the system, especially into the FCHQ filter room. On 11 January 1940, an operations research report on the Dowding system concluded that the filter room had been intended to correlate radar reports, but had developed into something much more complicated. Too much control took place in the filter room, which was producing results with "appallingly low standards". Given the success of the FCHQ filter room, it is unclear whether the report was inaccurate or if the problems had been solved by the time of the Battle of Britain.^[33]

It was known that the filter room could be overwhelmed by a high volume of reports, and it was a constant complaint that it was a single point of failure in reports from OR and in the RAF and Air Ministry. Most critics wanted the filter room to be moved from Bentley Priory to Group commands, lowering the reporting volume at each location and providing duplication. Dowding refused the change, leading to increasing friction with other commanders. Information overload occurred on several occasions and the filter room had to ask CH stations to stop reporting but this little effect on them capabilities and later, stations reported only basic information for multiple formations as a single plot.^[33]

The TR. 9D HF radio telephone set in fighters at the time of the Battle of Britain had two channels and the operating frequencies of the two could only be selected before take-off. One channel was used for voice communication with sector control, while the other was used by "pip-squeak". With only one voice channel, set to a squadron-specific frequency, the TR.9D limited the ability to co-ordinate with other squadrons. The set was low power, with a range of about 40 miles (64 kilometres) air-to-ground and 5 mi (8.0 km) air-to-air (a function of the antennas used in air and on the ground), which presented numerous problems with reception quality. The TR. 9 originally operated on a band that was relatively empty but by the time of the war it was much busier and interference was a constant problem.^[34]

Chain Home could only produce information of aircraft in "front" of the antennas, typically off-shore and the reporting system relied on the OC once the raid was over land. The OC, using sight, could provide little information at night, in bad weather or through overcast. During the Battle of Britain the weather was unusually good, the so-called "fighter's summer" and raids took place only when the weather allowed the bombers to see their targets.^{[35][36][lower-alpha 9]} The system failed to work against high-altitude raids that took place late in the battle.

The effectiveness of the system was influenced by personal and inter-group rivalries within the RAF command, particularly between 11 Group and 12 Groups whose commanders constantly bickered. Trafford Leigh-Mallory, commander of 12 Group, had originally been slated to take over 11 Group command but it went to Keith Park instead. Leigh-Mallory felt further slighted by Dowding because 12 Group had to defend 11 Group airfields while 11 Group attacked the Germans.^[37]

Dowding failed to centralise a command structure at FCHQ, which meant that group commanders controlled their own battle and could request but not demand support from other groups. During the battle, Leigh-Mallory repeatedly failed to send his fighters to cover 11 Group airfields, preferring instead to build his "Big Wing" formations to attack the Luftwaffe. Big Wings took time to assemble and were often incomplete as the Germans flew away and contributed little to the early stages of the battle.^[37] Dowding's inertia in this was held against him and led to his dismissal on 24 November 1940.^[38]

Aftermath

GCI radars allowed a station to provide detection, identification (IFF) and fighter direction, eliminating the need for the complex reporting chains of the Dowding system.

During the use of the system, Dowding resisted suggestions to move the filter room to the group to reduce demand on the FCHQ filter room, as well as provide redundancy. The matter was raised several times, the last time on 27 September, when the Air Council's request was once again dismissed by Dowding, who was summoned to the Air Staff on 1 October and was forced to devolve command, although he delayed this until all fighters were equipped with new IFF systems.^[33]

A few weeks later, Dowding was removed from command, perhaps due in part to his failure to come up with solutions to The Blitz and the groups soon had their own filter rooms. The introduction of ground-controlled interception radars (GCI) in the winter of 1940–41 allowed more devolution of command because sector controllers could directly detect and control the aircraft in their area.^[33] Working with IFF, now widely used, the GCI display eliminated the need for separate detection and plotting, as well as the communications links and manpower needed to operate the reporting system.^[39] The system remained in use for the rest of the war for daytime missions, both for (rare) defensive situations as well providing support for aircraft supporting offensive daytime raids during 1943 and later.

After the war the fighter control system was largely demobilized. The explosion of the Soviet atomic bomb in 1949 and the presence of Tupolev Tu-4 "Bull" aircraft that could deliver it to the UK, led to the rapid construction of the ROTOR system. ROTOR re-used many existing GCI and CH systems with more sophisticated control rooms in fortified underground bunkers. ROTOR was itself replaced by Type 80 radar Master Control rooms and then the Linesman/Mediator system in the 1960s.^[40]

Notes

References

Citations

Bibliography

Further reading

External links

Wikimedia Commons has media related to Dowding system.

• The Filter Room - WW2 - Radar Command, World War II film on the role of the Filter Room.