Birch's law

Birch's law establishes a linear relation of the compressional wave velocity vp of rocks and minerals of a constant average atomic weight Mavg with density as:

for some function a(x).[1]

Birch's Law was discovered by Francis Birch and allows for the seismic speed of a P-wave to be represented as a function of with regard to the atomic weight of the substance the wave is moving through.[2]

Applications of Birch's Law

Birch's law can be used in the discussion of geophysical data. The law is used in forming compositional and mineralogical models of the mantle by using the change in the velocity of the seismic wave and its relationship with a change in density of the material the wave is moving in. Birch's law is used in determining chemical similarities in the mantle as well as the discontinuities of the transition zones. Birch's Law can also be employed in the calculation of an increase of velocity due to an increase in the density of material.[3]

Shortcomings with Birch's Law

It had been previously assumed that the velocity density relationship is constant. That is, that Birch's Law will hold true any case, but as you look deeper into the mantle, the relationship does not hold true for the increased pressure that would be reached as you look deeper into the mantle near the Transition zone (Earth). In such cases where the assumption was made past the Transition zone (Earth), the solutions may need to be revised. In future cases, other Laws may be needed to determine the velocities at high pressures.[4]

Solving Birch's law experimentally

The relationship between the density of a material and the velocity of a P wave moving through the material was noted when research was conducted on waves in different materials. In the experiment, a pulse of voltage is applied to a circular plate of polarized barium titanate ceramic (the transducer) which is attached to the end of the material sample. The added voltage creates vibrations in the sample. Those vibrations travel through the sample to a second transducer on the other end. The vibrations are then converted into an electrical wave which is viewed on an oscilloscope to determine the travel time. The velocity is the lender of the damper decided by the wave's travel time. The resulting relationship between the density of the material and the discovered velocity is known as Birch's law.[5]

Velocity of compressional waves in rocks

The below table shows the velocities for different rocks ranging in pressure from 10 bars to 10,000 bars. It represents the how the change in density, as given in the second column, is related to the velocity of the P wave moving in the material. An increase in the density of the material leads to an increase in the velocity which can be determined using Birch's Law.

See also

References

  1. Poirier, Jean-Paul (2000). Introduction to the physics of the earth's interior (2nd ed.). Cambridge [u.a.]: Cambridge Univ. Press. p. 80. ISBN 9780521663922.
  2. Weisstein, Eric. "Birch's Law". Wolfram Research. Retrieved 2 February 2015.
  3. Liebermann, Robert; Ringwood, A. E. (October 20, 1973). "Birch's Law and Polymorphic Phase Transformations". Journal of Geophysical Research. 78 (29): 6926–6932. Bibcode:1973JGR....78.6926L. doi:10.1029/JB078i029p06926.
  4. Birch, F. (1961). "The velocity of compressional waves in rocks to 10 kilobars. Part 2". Journal of Geophysical Research. 66 (7): 2199–2224. Bibcode:1961JGR....66.2199B. doi:10.1029/JZ066i007p02199.
  5. 1 2 Birch, Francis (April 1960). "The Velocity of Compressional Waves in Rocks to 10 Kilobars, Part 1". Journal of Geophysical Research. 65 (4): 1083–1102. Bibcode:1960JGR....65.1083B. doi:10.1029/JZ065i004p01083.
This article is issued from Wikipedia - version of the 6/9/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.