Autodyne

Schematic of an early autodyne receiver.

The autodyne circuit was an improvement to radio signal amplification using the De Forest Audion vacuum tube amplifier. By allowing the tube to oscillate at a frequency slightly different from the desired signal, the sensitivity over other receivers was greatly improved.[1] The autodyne circuit was invented by Edwin Howard Armstrong of Columbia University, New York, NY. He inserted a tuned circuit in the output circuit of the Audion vacuum tube amplifier. By adjusting the tuning of this tuned circuit, Armstrong was able to dramatically increase the gain of the Audion amplifier. Further increase in tuning resulted in the Audion amplifier reaching self-oscillation.

This oscillating receiver circuit meant that the newly produced CW or continuous wave transmissions could be aurally decoded. Previously only spark, ICW (Interrupted Continuous Wave) signals which were produced by a motor chopping or turning the signal quickly on and off at an audio rate, or modulated continuous wave (MCW), could be decoded.

When the autodyne oscillator was advanced to self-oscillation, continuous wave Morse code dots and dashes would be clearly heard as a series of beeps, instead of an all but impossible to decode series of thumps. Spark and chopped CW (ICW) had audio tones which didn't require an oscillating detector to extract from the radio signal. Such a regenerative circuit is capable of receiving weak signals, if carefully coupled to an antenna. Antenna coupling interacts with tuning, making optimum adjustments difficult.

Heterodyne detection

Main article: Heterodyne

Damped wave transmission

Early transmitters emitted damped waves, which were decaying sinewaves at the transmission frequency. Bursts were made at an audible frequency.[2] The damped waves were a result of the available technologies to generate radio frequencies. See spark gap transmitter. The transmitters could be keyed on and off to send Morse code.

Receivers could be made with a tuned circuit, a crystal detector, and a headphone. The headphone would respond to the detected bursts, and the operator could copy the Morse code. The received signal was not a sinewave. Instead of a crystal detector, a Fleming valve (tube diode) could be used; it was a stable detector, but not very sensitive. Even better was a using a vacuum triode because it provided some amplification.[3] The regenerative receiver supplied even more gain, but required careful adjustment.[4]

Undamped wave transmission

Damped wave transmission had drawbacks, and the focus shifted to undamped waves or continuous wave (CW) transmission. The arc converter could produce high power CW transmissions.

The typical damped wave receiver was ineffective for receiving CW because CW had no audible modulation. Several methods were employed to generate an audible tone at the receiver: (1) a chopper, (2) a variable condensor with rotating plates (slope demodulation), (3) a tikker, (4) a separate heterodyne, and (5) the autodyne.[5]

Fessenden researched the heterodyne detector.

Application

The autodyne was popular at the beginning of the Depression (ca early 1930s).[6]

More recently, autodyne converters are employed in radio receivers for the AM and FM broadcast band. A single transistor combines the functions of amplifier, mixer and local oscillator of an otherwise conventional superheterodyne receiver. Such a stage accepts as input the antenna signal, and provides an output to the intermediate frequency amplifier. In this application, the transistor is made to self-oscillate at the local oscillator frequency.

The autodyne detector has appeared in specialized fields in the 1960s through the 1990s.[7][8][9][10]

See also

References

  1. ↑ Bureau of Standards 1922, p. 503
  2. ↑ Bureau of Standards 1922, p. 419
  3. ↑ Bureau of Standards 1922, p. 426
  4. ↑ Bureau of Standards 1922, p. 427
  5. ↑ Bureau of Standards 1922, p. 430
  6. ↑ P. R. Mallory Co. 1942, p. 32 Autodyne First Detector Combinations: "The Autodyne reached it greatest popularity and development during the beginning of the depression...."
  7. ↑ Bruin, F.; Van Soest, P. C. (September 1960), "Transistorized Autodyne Detector for ESR and NSR", Review of Scientific Instruments, 31 (8): 909, doi:10.1063/1.1717092
  8. ↑ Brandwein, Leonard; Lipsicas, Max (September 1970), "Application of Frequency Locking and Control to an Autodyne Oscillating NMR Detector", Review of Scientific Instruments, 41 (9): 1293–1295, doi:10.1063/1.1684797
  9. ↑ Medvedev, Iu. V.; Raksina, F. P.; Popov, L. N. (April 1978), "Autodyne Detector of Optical Signals", Radiotekhnika (in Russian), 33: 32–35, Bibcode:1978RaT....33...32M
  10. ↑ Nowakowski, N; Gutkowicz-Krusin, E.; Lind, G. (20 April 1990), Innovative Techniques for High-Resolution Imaging and Precision Tracking, AD-A221380. Lidar target tracking with autodyne.

External links

This article is issued from Wikipedia - version of the 10/17/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.